Install HP SNMP Agents for Citrix XenServer 6.x

Console output
warning: compat-libstdc++-296-2.96-138.i386.rpm: Header V3 DSA signature: NOKEY, key ID 897da07a
warning: lm_sensors-2.10.0-3.1.i386.rpm: Header V3 DSA signature: NOKEY, key ID 37017186
Installing ‘HP SNMP Agents for XenServer’…
warning: compat-libstdc++-296-2.96-138.i386.rpm: Header V3 DSA signature: NOKEY, key ID 897da07a
warning: lm_sensors-2.10.0-3.1.i386.rpm: Header V3 DSA signature: NOKEY, key ID 37017186
Preparing… ########################################### [100%]
1:hp-health ########################################### [ 11%]
Please read the Licence Agreement for this software at
/opt/hp/hp-health/hp-health.license
By not removing this package, you are accepting the terms
of the “HP Proliant Essentials Software End User License Agreement”.
==============================================================================
NOTE: To activate the software contained in this package, you must type:
/etc/init.d/hp-health start
/etc/init.d/hp-asrd start
as ‘root’ user.
==============================================================================
The hp-health RPM has installed successfully.
2:lm_sensors ########################################### [ 22%]
3:hp-snmp-agents ########################################### [ 33%]
Please read the Licence Agreement for this software at
/opt/hp/hp-snmp-agents/hp-snmp-agents.license
By not removing this package, you are accepting the terms
of the “HP Proliant Essentials Software End User License Agreement”.
==============================================================================
NOTE: In order to activate the software contained in this package, you must
type ‘/sbin/hpsnmpconfig’ as ‘root’ user.
Once configuration is completed start the agents by typing
/etc/init.d/hp-snmp-agents start
==============================================================================
4:OpenIPMI-libs ########################################### [ 44%]
5:OpenIPMI ########################################### [ 56%]
6:compat-libstdc++-296 ########################################### [ 67%]
Detected Xen Server 6.0.2-53456p
Creating hpsmh user and group…
Adding hpsmh user to the root group
7:hpsmh ########################################### [ 78%]
**********************************************************
* System Management Homepage installed successfully with *
* default configuration values. To change the default *
* configuration values, type the following command at *
* the root prompt: *
* *
* /opt/hp/hpsmh/sbin/smhconfig *
* *
**********************************************************
hpsmhd already stopped
Starting hpsmhd: hpsmhd: apr_sockaddr_info_get() failed for xenserverxd01
hpsmhd: Could not reliably determine the server’s fully qualified domain name, u sing 127.0.0.1 for ServerName
[ OK ]
8:hp-smh-templates ########################################### [ 89%]
Please read the Licence Agreement for this software at
/opt/hp/hp-smh-templates/hp-smh-templates.license
By not removing this package, you are accepting the terms
of the “HP Proliant Essentials Software End User License Agreement”.
========================================================================
NOTE: To activate the software contained in this package, you must type:
/etc/init.d/hpsmhd restart or service hpsmhd restart
as ‘root’ user.
=========================================================================
9:hp-agents-xs-config ########################################### [100%]
Starting ipmi drivers: [ OK ]
Activating HP Agents…
==============================================================================
NOTE: New snmpd.conf entries were added to the top of /etc/snmp/snmpd.conf
==============================================================================
Following environment variables were used to configure snmpd/agents:
CMASKIPSNMPCONFIG
CMALOCALHOSTRWCOMMSTR
CMALOCALHOSTROCOMMSTR
CMAMGMTSTATIONIPORDNS
CMAMGMTSTATIONRWCOMMSTR
CMAMGMTSTATIONROIPORDNS
CMAMGMTSTATIONROCOMMSTR
CMADEFTRAPCOMMSTR
CMATRAPDESTINATIONIPORDNS
CMATRAPDESTINATIONCOMMSTR
snmpd is started
Using Proliant Standard
IPMI based System Health Monitor
Shutting down Proliant Standard
IPMI based System Health Monitor (hpasmlited): [ OK ]
Starting Proliant Standard
IPMI based System Health Monitor (hpasmlited):
OK ]
Shutting down NIC Agent Daemon (cmanicd):[FAILED]
Shutting down Storage Event Logger (cmaeventd): [FAILED]
Shutting down FCA agent (cmafcad): [FAILED]
Shutting down SAS agent (cmasasd): [FAILED]
Shutting down IDA agent (cmaidad): [FAILED]
Shutting down IDE agent (cmaided): [FAILED]
Shutting down SCSI agent (cmascsid): [FAILED]
Shutting down Health agent (cmahealthd): [FAILED]
Shutting down Standard Equipment agent (cmastdeqd): [FAILED]
Shutting down Host agent (cmahostd): [FAILED]
Shutting down Threshold agent (cmathreshd): [FAILED]
Shutting down RIB agent (cmasm2d): [FAILED]
Shutting down Rack Infrastructure Info Srv (cpqriisd): [FAILED]
Shutting down Rack agent (cmarackd): [FAILED]
Shutting down Performance agent (cmaperfd): [FAILED]
Shutting down SNMP Peer (cmapeerd): [FAILED]
Starting Health agent (cmahealthd): [ OK ]
Starting Standard Equipment agent (cmastdeqd): [ OK ]
Starting Host agent (cmahostd): [ OK ]
Starting Threshold agent (cmathreshd): [ OK ]
Starting RIB agent (cmasm2d): [ OK ]
Starting Rack Infrastructure Info Srv (cpqriisd): [ OK ]
Starting Rack agent (cmarackd): [ OK ]
Starting Performance agent (cmaperfd): [ OK ]
Starting SNMP Peer (cmapeerd): [ OK ]
Starting Storage Event Logger (cmaeventd): [ OK ]
Starting FCA agent (cmafcad): [ OK ]
Starting SAS agent (cmasasd): [ OK ]
Starting IDA agent (cmaidad): [ OK ]
Starting IDE agent (cmaided): [ OK ]
Starting SCSI agent (cmascsid): [ OK ]
Starting NIC Agent Daemon (cmanicd): [ OK ]
Stopping hpsmhd: [ OK ]
Starting hpsmhd: hpsmhd: apr_sockaddr_info_get() failed for xenserverxd01
hpsmhd: Could not reliably determine the server’s fully qualified domain name, using 127.0.0.1 for ServerName
[ OK ]
Configuration Complete!
Memory required by all installed packages: 915668992
Truncating to static-max: 789839872
Setting VM.memory_target: 789839872
Pack installation successful.

Leave a comment

Your email address will not be published. Required fields are marked *

WordPress Appliance - Powered by TurnKey Linux